析晶污垢生长影响因素概述

结垢问题存在于各个行业,尤其在油田表现更甚。但材料表面特性对油田采出水中析晶污垢的影响并没有得到太多关注。主要对影响析晶污垢生长的三种主要表面特性因素进行简要综述。     

Composition-dependent xBa(Zr0.2Ti0.8)O3-(1-x)(Ba0.7Ca0.3)TiO3 bulk ceramics for high energy storage applications

This work reports the composition dependent microstructure, dielectric, ferroelectric and energy storage properties, and the phase transitions sequence of lead free xBa(Zr_0.2Ti_0.8)O₃-(1-x)(Ba_0.7Ca_0.3)TiO₃ [xBZT-(1-x)BCT] ceramics, with x?=?0.4, 0.5 and 0.6, prepared by solid state reaction method. The XRD and Raman scattering results confirm the coexistence of rhombohedral and tetragonal phases at room temperature (RT). The temperature dependence of Raman scattering spectra, dielectric permittivity and polarization points a first phase transition from ferroelectric rhombohedral phase to ferroelectric tetragonal phase at a temperature (T_R-T) of 40?°C and a second phase transition from ferroelectric tetragonal phase - paraelectric pseudocubic phase at a temperature (T_T-C) of 110?°C. The dielectric analysis suggests that the phase transition at T_T-C is of diffusive type and the BZT-BCT ceramics are a relaxor type ferroelectric materials. The composition induced variation in the temperature dependence of dielectric losses was correlated with full width half maxima (FWHM) of A₁, E(LO) Raman mode. The saturation polarization (P_s) ≈8.3?μC/cm² and coercive fields ≈2.9?kV/cm were found to be optimum at composition x?=?0.6 and is attributed to grain size effect. It is also shown that BZT-BCT ceramics exhibit a fatigue free response up to 10⁵ cycles. The effect of a.c. electric field amplitude and temperature on energy storage density and storage efficiency is also discussed. The presence of high T_T-C (110?°C), a high dielectric constant (ε_r ≈?12,285) with low dielectric loss (0.03), good polarization (P_s ≈?8.3?μC/cm²) and large recoverable energy density (W?=?121?mJ/cm³) with an energy storage efficiency (η) of 70% at an electric field of 25?kV/cm in 0.6BZT-0.4BCT ceramics make them suitable candidates for energy storage capacitor applications.     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

冶金矿物和产品水分测定问题探讨

水分测定是冶金行业中矿产原料和产品分析的重要内容,主要包括交货水分、湿存水、化合水等测定类别。尽管水分测定方法本身相对简单,但其涉及到矿物原料、产品结算交割以及其他化学分析的校正计算,属于重要的基础性测定方法。各类矿物、产品几乎都有相应水分测定的国家标准、行业标准,部分还是从国外ISO标准体系中采标而来。文章系统介绍并比较各类矿物原料、产品中交货水分、明水、湿存水、化合水等类别的测定方法。由于ISO标准体系中湿存水含义和国内标准体系湿存水含义有较大差异,其测定操作和用途也有不同,使用空气平衡样品和密封原始样品将会得到数据差异较大的湿存水数据,两种湿存水含义需要明确区分。湿存水对化学称样量、灼减量、化合水的测定有影响,需要用湿存水进行水分校正,才能得到更精确的结果。     

凌庄子水厂保水堰流量系数试验

凌庄子水厂蓄水池进水口处有一保水堰,为非标准薄壁堰,不能使用已有堰流公式对其过流量进行准确计算。为了得出较为精确的过流流量,按照重力相似准则制作几何比尺为1∶5的模型进行试验研究。在已有自由出流公式的基础上,对自由出流流量系数进行修正并对淹没情况下流量变化过程进行研究。对该非标准堰自由出流流量系数的实测值与经验值进行分析比较,发现堰板槽降低了实际自由出流过流能力。淹没出流的流量系数主要与下游尾水位有关,试验中形成的淹没式堰流受实际堰型尺寸影响,下游尾水位和堰上水位近似相等,不完全适用已有淹没出流流量公式,通过试验给出了修正淹没系数随h/p的变化关系。结果表明利用堰前、堰后水位初步计算过流流量是可行的,可为该工程提供参考,也可为实际工程中非标准矩形堰的流量计算提供思路。     

一起电镀企业失火事故后的思考

步入新时代,我国经济实现了跨越式发展,企业面临着更多的发展机遇与挑战,但只有牢牢守住"安全生产"这一警戒线,一切生产经营活动才能真正创造经济价值.现介绍一起电镀企业失火事故,通过分析认定事故原因,并结合类似事故案例,探寻事故频发的深层原因,提出有效的预防对策和措施,希望引发从事电镀生产及安全管理、消防工作人员的深度思考,提供可借鉴的有益经验,为企业安全生产保驾护航.     

汽车锁零部件碱性锌镍合金电镀工艺

介绍了汽车锁零部件碱性挂镀锌镍合金电镀生产线的开发过程,包括前期市场调研、中期小槽试验、后期成本核算、电镀工艺流程确定、废水处理工艺制定以及阳极膜应用可行性分析。     

Effect of microwave power irradiation on TiO2 nano-structures and binder free paste screen printed dye sensitized solar cells

Titanium dioxide (TiO₂) nanostructures (nanorods and nanoparticles) were prepared using a low-cost microwave irradiation method from a polyol medium of glycerol. Titanium glycerolate and TiO₂ powders were obtained in the glycerol medium for the first time with four different power densities (240?W, 480?W, 720?W, 960?W) of irradiation using a domestic microwave oven of 2.45?GHz, to understand the impact of power on morphology tuning. The structural and morphological features of the titanium glycerolate and TiO₂ powders were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Raman spectra analysis. The TiO₂ was successfully used in the fabrication of photovoltaic devices and as a proof-of-concept binder free paste was prepared and successfully employed for photo-anode using screen printing on the fluorine-doped tin oxide substrate.